展开
托驰（上海）工业传感器有限公司
托驰（上海）工业传感器有限公司 ☰
当前位置： 首页>> 产品展示 >> 韩国Dacell传感器 >>韓國Dacell仪表DN500A 510A

韓國Dacell仪表DN500A 510A

价格 电议
更新时间
2019-02-08 05:45:02
起订量
1件起批
服务
 资质已审查
发货地
上海市 嘉定区
货期
近期热度
次浏览
立即询报价

产品介绍

 

  • SPECIFICATIONS
ANALOG INPUT AND A/D CONVERSION
Load cell excitation 10VDC±5% 320mA
Input Sensitivity 0.45?/D
Zero adjustment range -0.6mV~42mV : combinations of 6bit dip switch
Input voltage Max. 32mV
impedance 10? (Min.)
noise 0.6?p.p or Less
A/D converter type : dual slope type
resolution : 1/65000 counts(16bits)
converting speed : 20times/sec
Non-linearity 0.01% of full scale
Temperature-drift zero ±20PPM/℃
span ±20PPM/℃
Overload tolerance 10% of full capacity
Display update rate 20 times/sec

DIGITAL SECTION
Display unit 12.7mm(1/2") 7digits
Annunciators steady zero tare gross auto print hold
Decimal point position 0 0.0 0.00 0.000
Keyboard ten key zero tare tare reset print gross/net grand total
sub total parts number hold reset auto code s/n&enter
DN510A : run standby sp1 sp2 sp3 sp4
External input signal opical-isolator
min. Division x1 x2 x5 x10 x20 x50
max. Display 550000
Rear panel Loadcell input : 5pin connector
External control : 5pin input terminal (zero tare tare reset/hold/print gross/hold reset/subprint)
DN510A : control relay : 7pin terminal

GENERAL
Data memory back-up appr. 10year
Power 100/110/120/220/240V AC ±10% 50/60? (factory preset)
Power consumption appr. 10w
Operating condition temperature : -10~40℃ (14~104℉)
humidity : 85% Rh Max. (non-condensing)
Net weight 2.3kg
Gross weight 3.0kg
Physical dimensions (WxDxH) 192x150x96mm / (WxDxH) 7.56x5.91x3.78inch
Fuse 250V/0.3A
  • FEATURES
  • Control for PACKER FILLER HOPPER CHECKER LIMIT SCALE etc.
  • Auto span calibration
  • 50 kind of parts number can be memorized
  • Watch-dog function installed for diagnostics
  • Data memory back up for over 10years
  • Front display window is covered by lexan film for the protecting of dust
  • Lock function for the protection of set-up mode
  • Weighting judgment by over & under setting when printer is connected
  • Three kinds of hold function (peak-hold and average-hold auto-hold)
  • Weight memory back up for up to 10years
  • Can drive up to 8pcs of load cell (350?)
  • Serial interface standard installed (RS-232C and CURRENT LOOP)
  • Can print the data & time count parts number weighing decision and sub/grand when printer is connected by option
DN 500A
  • The external field switch can be directly connected to 5pin terminal located at the rear panel for the remote control of some key-board functions (ZERO TARE TARE RESET HOLD HOLD RESET PRINT SUB PRINT NET/GROSS)
DN 510A
  • The external field switch can be directly connected to 5pin terminal located at the rear panel for the remote control of some key-board functions (START STOP ZERO TARE TARE RESET HOLD HOLD RESET PRINT SUB PRINT NET/GROSS)
  • 4 Step control (SP1 SP2 SP3 SP4)
  • 6 control relay built-in (SP1 SP2 SP3 SP4 FINISH NEAR ZERO)
  • Relay output mode (LIMIT PACKER CHECKER1 CHECKER2)
Option
OP1 Printer I/F : Centronics Parallel
OP2 Analod Out : V - out(0~10V)
OP3 Analod Out : I - out(4~20mA)
OP4 Serial I/F : RS 422 RS485
OP5 BCD Out-put
  • DIMENSIONS

详细资料